DZC series
DigiFlex® Performance™, CANopen, Z-Drives (plug-in)
The DZC series is part of the Z-Drives family of plug-in servo drives. Experience the advantage of both plug-in integration and DigiFlex® Performance™ in one solution.
- Encoder
- Overview
- Downloads & Support
Encoder Feedback |
|
These drives support 5V incremental encoder feedback. Hall sensors are recommended for initial commutation, but are not required. These drives can be configured to run without Halls by using "Phase Detect" on startup (Wake & Shake). |
Can't find exactly what you need? Consider a modified or custom solution...
Model Number |
Power |
Command Signal |
Inputs and Outputs |
|||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Voltage (V) |
Rated (kW) |
Current (A) |
±10V |
Step |
Enc |
PWM |
Network |
Analog |
Digital 5V |
Digital 24V |
||||||||
AC |
DC |
Logic* |
Peak |
Cont. |
Peak |
Cont. |
In |
Out |
In |
Out |
In |
Out |
||||||
| < sort > | ||||||||||||||||||
| {Model} | {InputVoltageACLow} - {InputVoltageACHigh} | {InputVoltageDCLow} - {InputVoltageDCHigh} | {ExternallySuppliedLogic} | {Peak_Power} | {Cont_Power} | {Peak_Current} | {Cont_Current} | {AnalogInputs} | {AnalogOutputs} | {DigitalInputs5V} | {DigitalOutputs5V} | {DigitalInputs24V} | {DigitalOutputs24V} | |||||
 |
|
|---|---|
The DZC-series is part of our Digiflex® Performance™ family. Please see our Digiflex® Performance™ page to see all options. |
|
Network |
CANOpen - For drive communication and control. |
Setup |
RS232 - For setup configuration with DriveWare software. |
Motors |
All models compatible with - Brushless, Brushed, Linear, Rotary, Voice Coil, Inductive Load, Closed Loop Vector (AC Induction). |
Feedback |
TTL Encoder - 5V incremental encoder feedback. Encoders are used for velocity and position mode feedback as well as sinusoidal commutation for brushless motors. Hall Sensors - Recommended for commutation of 3Φ brushless motors. Can be used for velocity feedback in Hall Velocity Mode. Configurable for 120° and 60° Hall spacing. |
Power |
DC Voltage Range - 10 - 175 VDC |
Command Source(s) |
CANopen - An open protocol for distributed automation and motion control. Distributed control reduces network bus traffic by giving the drives more intelligence. Drives can be preconfigured to respond to commands with specific move profiles. Therefore fewer messages need to be sent and more drives can operate on the network. +/-10V - Drives accept single ended and differential signals. Encoder Following (Electronic Gearing) - 'Slave' one system off of another. PWM and Direction - Use PWM & Direction commands to control torque or velocity. |
I/O |
Events and Signals - Analog and Digital I/O can be configured for over 60 events and signals. Analog - See individual drive specification for resolution and quantity. Digital (TTL) - See individual drive specifications for quantity. |
Mode |
Torque - The input command controls the output current (torque). The servo drive will adjust to disturbances and maintain the commanded current. This is the suggested mode if an external controller is used which can close the velocity or position loops. Hall Velocity - The input command controls the motor velocity. This mode uses the motor's Hall sensors for velocity feedback. Due to the low resolution of the Hall sensors, this mode is not recommended for low speed applications. In high speed applications this mode can provide excellent performance. Velocity - The input command controls the motor velocity. The drive uses high resolution feedback on the motor or load to close the velocity loop. Position - The input command controls the motor position. The drive uses high resolution feedback on the motor or load to close the position loop. |
