Click for more information
DZX series
DigiFlex® Performance™, Extended Environment, Z-Drives (plug-in)
Experience the advantage of plug-in integration, DigiFlex® Performance™ and extended environment capabilities in one solution. These servo drives are designed to operate in harsh environments including hot, cold, shock and vibration. All models operate with both brushed and brushless motors and inductive loads.
The DZX-series is part of our Extended Environment offering. Please see our Extended Environment page to see all options.
Models are categorized by the network type - RS485/232 or CANopen:
- RS485/232
- CANopen
- Overview
- Downloads & Support
Encoder Feedback |
|
These drives support 5V incremental encoder feedback. Hall sensors are recommended for initial commutation, but are not required. These drives can be configured to run without Halls by using "Phase Detect" on startup (Wake & Shake). |
Can't find exactly what you need? Consider a modified or custom solution...
Model Number |
Power |
Command Signal |
Inputs and Outputs |
|||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Voltage (V) |
Rated(kW) |
Current (A) |
±10V |
Step |
Enc |
PWM |
Network |
Analog |
Digital 5V |
Digital 24V |
||||||||
AC |
DC |
Logic* |
Peak |
Cont. |
Peak |
Cont. |
In |
Out |
In |
Out |
In |
Out |
||||||
| < sort > | ||||||||||||||||||
| {Model} | {InputVoltageACLow} - {InputVoltageACHigh} | {InputVoltageDCLow} - {InputVoltageDCHigh} | {ExternallySuppliedLogic} | {Peak_Power} | {Cont_Power} | {Peak_Current} | {Cont_Current} | {AnalogInputs} | {AnalogOutputs} | {DigitalInputs5V} | {DigitalOutputs5V} | {DigitalInputs24V} | {DigitalOutputs24V} | |||||
* Logic Supply Voltage.
|
Encoder Feedback |
|
These drives support 5V incremental encoder feedback. Hall sensors are recommended for initial commutation, but are not required. These drives can be configured to run without Halls by using "Phase Detect" on startup (Wake & Shake). |
Can't find exactly what you need? Consider a modified or custom solution...
Model Number |
Power |
Command Signal |
Inputs and Outputs |
|||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Voltage (V) |
Rated(kW) |
Current (A) |
±10V |
Step |
Enc |
PWM |
Network |
Analog |
Digital 5V |
Digital 24V |
||||||||
AC |
DC |
Logic* |
Peak |
Cont. |
Peak |
Cont. |
In |
Out |
In |
Out |
In |
Out |
||||||
| < sort > | ||||||||||||||||||
| {Model} | {InputVoltageACLow} - {InputVoltageACHigh} | {InputVoltageDCLow} - {InputVoltageDCHigh} | {ExternallySuppliedLogic} | {Peak_Power} | {Cont_Power} | {Peak_Current} | {Cont_Current} | {AnalogInputs} | {AnalogOutputs} | {DigitalInputs5V} | {DigitalOutputs5V} | {DigitalInputs24V} | {DigitalOutputs24V} | |||||
* Logic Supply Voltage.
 |
|
|---|---|
Designed to assist system compliance toward:
|
|
Network |
(DZXR-series) RS485/232 - For communication and control. |
(DZXC-series) CANOpen - For drive communication and control. |
|
Setup |
RS232 - For setup configuration with DriveWare software. |
Motors |
All models compatible with - Brushless, Brushed, Linear, Rotary, Voice Coil, Inductive Load, Closed Loop Vector (AC Induction). |
Feedback |
TTL Encoder - 5V incremental encoder feedback. Encoders are used for velocity and position mode feedback as well as sinusoidal commutation for brushless motors. Hall Sensors - Recommended for commutation of 3Φ brushless motors. Can be used for velocity feedback in Hall Velocity Mode. Configurable for 120° and 60° Hall spacing. |
Power |
DC Voltage Range - 10 - 80 VDC |
Command Source(s) |
±10V Analog - Drives accept single ended and differential signals. Step & Direction - Use stepper commands to control a servo motor. Encoder Following (Electronic Gearing) - 'Slave' one system off of another. PWM & Direction - Use PWM & Direction commands to control torque or velocity. RS485/232 - The ADVANCED Motion Controls’ serial protocol is a byte‐based, binary, master/slave protocol to access drive ‘commands’. The drive commands provide read or write access to drive parameters with each command containing one or more parameters. CANopen - An open protocol for distributed automation and motion control. Distributed control reduces network bus traffic by giving the drives more intelligence. Drives can be preconfigured to respond to commands with specific move profiles. Therefore fewer messages need to be sent and more drives can operate on the network. |
I/O |
Events and Signals - Analog and Digital I/O can be configured for over 60 events and signals. Analog - See individual drive specification for resolution and quantity. Digital (TTL) - See individual drive specifications for quantity. |
Mode |
Torque - The input command controls the output current (torque). The servo drive will adjust to disturbances and maintain the commanded current. This is the suggested mode if an external controller is used which can close the velocity or position loops. Hall Velocity - The input command controls the motor velocity. This mode uses the motor's Hall sensors for velocity feedback. Due to the low resolution of the Hall sensors, this mode is not recommended for low speed applications. In high speed applications this mode can provide excellent performance. Velocity - The input command controls the motor velocity. The drive uses high resolution feedback on the motor or load to close the velocity loop. Position - The input command controls the motor position. The drive uses high resolution feedback on the motor or load to close the position loop. |
